The trick is simple, and many of those who deal with HA cluster get at least once to such a setup – have HA cluster without HA.
Yep. Single node, just to make sure you know how to get this system to play.
I have just completed it with Linux Heartbeat, and wish to share the example of a setup single-node cluster, with DRBD.
First – get the packages.
It took me some time, but following Linux-HA suggested download link (funny enough, it was the last place I’ve searched for it) gave me exactly what I needed. I have downloaded the following RPMS:
heartbeat-2.0.7-1.c4.i386.rpm
heartbeat-ldirectord-2.0.7-1.c4.i386.rpm
heartbeat-pils-2.0.7-1.c4.i386.rpm
heartbeat-stonith-2.0.7-1.c4.i386.rpm
perl-Mail-POP3Client-2.17-1.c4.noarch.rpm
perl-MailTools-1.74-1.c4.noarch.rpm
perl-Net-IMAP-Simple-1.16-1.c4.noarch.rpm
perl-Net-IMAP-Simple-SSL-1.3-1.c4.noarch.rpm
I was required to add up the following RPMS:
perl-IO-Socket-SSL-1.01-1.c4.noarch.rpm
perl-Net-SSLeay-1.25-3.rf.i386.rpm
perl-TimeDate-1.16-1.c4.noarch.rpm
I have added DRBD RPMS, obtained from YUM:
drbd-0.7.21-1.c4.i386.rpm
kernel-module-drbd-2.6.9-42.EL-0.7.21-1.c4.i686.rpm (Note: Make sure the module version fits your kernel!)
As soon as I finished searching for dependent RPMS, I was able to install them all in one go, and so I did.
Configuring DRBD:
DRBD was a tricky setup. It would not accept missing destination node, and would require me to actually lie. My /etc/drbd.conf looks as follows (thanks to the great assistance of linux-ha.org):
resource web {
protocol C;
incon-degr-cmd “echo ‘!DRBD! pri on incon-degr’ | wall ; sleep 60 ; halt -f”; #Replace later with halt -f
startup { wfc-timeout 0; degr-wfc-timeout 120; }
disk { on-io-error detach; } # or panic, …
syncer {
group 0;
rate 80M; #1Gb/s network!
}
on p800old {
device /dev/drbd0;
disk /dev/VolGroup00/drbd-src;
address 1.2.3.4:7788; #eth0 network address!
meta-disk /dev/VolGroup00/drbd-meta[0];
}
on node2 {
device /dev/drbd0;
disk /dev/sda1;
address 192.168.99.2:7788; #eth0 network address!
meta-disk /dev/sdb1[0];
}
}
I have had two major problems with this setup:
1. I had no second node, so I left this “default” as the 2nd node. I never did expect to use it.
2. I had no free space (non-partitioned space) on my disk. Lucky enough, I tend to install Centos/RH using the installation defaults unless some special need arises, so using the power of the LVM, I have disabled swap (swapoff -a), decreased its size (lvresize -L -500M /dev/VolGroup00/LogVol01), created two logical volumes for DRBD meta and source (lvcreate -n drbd-meta -L +128M VolGroup00 && lvcreate -n drbd-src -L +300M VolGroup00), reformatted the swap (mkswap /dev/VolGroup00/LogVol01), activated the swap (swapon -a) and formatted /dev/VolGroup00/drbd-src (mke2fs -j /dev/VolGroup00/drbd-src). Thus I have now additional two volumes (the required minimum) and can operate this setup.
Solving the space issue, I had to start DRBD for the first time. Per Linux-HA DRBD Manual, it had to be done by running the following commands:
modprobe drbd
drbdadm up all
drbdadm — –do-what-I-say primary all
This has brought the DRBD up for the first time. Now I had to turn it off, and concentrate on Heartbeat:
drbdadm secondary all
Heartbeat settings were as follow:
/etc/ha.d/ha.cf:
use_logd on #?Or should it be used?
udpport 694
keepalive 1 # 1 second
deadtime 10
initdead 120
bcast eth0
node p800old #`uname -n` name
crm yes
auto_failback off #?Or no
compression bz2
compression_threshold 2
I have also created a relevant /etc/ha.d/haresources, although I’ve never used it (this file has no importance when using “crm=yes” in ha.cf). I did, however, use it as a source for /usr/lib/heartbeat/haresources2cib.py:
p800old IPaddr::1.2.3.10/8/1.255.255.255 drbddisk::web Filesystem::/dev/drbd0::/mnt::ext3 httpd
It is clear that the virtual IP will be 1.2.3.10 in my class A network, and DRBD would have to go up before mounting the storage. After all this, the application would kick in, and would bring up my web page. The application, Apache, was modified beforehand to use the IP 1.2.3.10:80, and to search for DocumentRoot in /mnt
Running /usr/lib/heartbeat/haresources2cib.py on the file (no need to redirect output, as it is already directed to /var/lib/heartbeat/crm/cib.xml), and I was ready to go.
/etc/init.d/heartbeat start (while another terminal is open with tail -f /var/log/messages), and Heartbeat is up. It took it few minutes to kick the resources up, however, I was more than happy to see it all work. Cool.
The logic is quite simple, the idea is very basic, and as long as the system is being managed correctly, there is no reason for it to get to a dangerous state. Moreover, since we’re using DRBD, Split Brain cannot actually endanger the data, so we get compensated for the price we might pay, performance-wise, on a real two-node HA environment following these same guidelines.
I cannot express my gratitude to http://www.linux-ha.org, which is the source of all this (adding up with some common sense). Their documents are more than required to setup a full working HA environment.
